Notes install Openwrt

Plusieurs bases sont a l'étude

• Le Flint 2 (GL-MT6000) de GL.iNet
• Le hAP ax S de Mikrotik
• Le banana-pi-bpi-r3
• Le banana-pi-bpi-r4
  • SD 32Go
• Le NanoPi R6S
• Turris Omnia (WRT3200, R7800, Omnia)
• NOAH6

Materiel EOL

• PC Engines APU4
• PC Engines APU6

Synthèse des spécifications

• alim. externe pour 220V euro
• DRAM 2-4GB DDR3 DRAM
• CPU
  • 64 bit et AES-NI
    • débit ≤ 500–700 Mbps : Celeron Gemini/Jasper‑Lake récent (ex. J4125/J4105/J3455)
    • débit >600–800 Mbps : Core i3
  • shared 2MB L2 cache.
• Storage
  • Boot depuis SD card (internal sdhci controller), external USB ou m.2 SATA
  • 1 M.2 SATA, longueur 2230/2242
  • SSD 120-240GB longueur correpondante
  • 1 slot M.2 2230 ( E‑Key PCIe x1/USB , compatible module Wi‑Fi AX200)
• Réseau
  • 4 Gigabit Ethernet avec NIC opensource (Intel i211/i210)
• wifi
  • firmware libre : Atheros compatible ath9k (AR9285, AR9462) limite 802.11n.
  • firmware blob : Intel AX200 (wifi 6) ou QCA ath10k
  • connecteurs RP‑SMA (antennes externes pour performance)
  • 2x RP‑SMA 5 dBi omnidirectionnelles
• I/O
  • DB9 serial port,
  • 2 USB 3.0 external
  • LEDs facade avant
  • interrupteur ON/OFF
• Firmware: coreboot si possible
• Cooling : fanless

• Sd 32Go

• Sd 32Go

• APU 4 - 4 GB AMD GX-412TC Quad core 1 GHz
• CPU: AMD Embedded G series GX-412TC, 1 GHz quad Jaguar core with 64 bit and AES-NI support, 32K data + 32K instruction cache per core, shared 2MB L2 cache.
• DRAM: 2 or 4 GB DDR3-1333 DRAM
• Storage: Boot from SD card (internal sdhci controller), external USB or m-SATA SSD. 1 SATA + power connector. mSATA is shared with miniPCI express.
• 12V DC, about 6 to 12W depending on CPU load. Jack = 2.5 mm, center positive
• Connectivity: 4 Gigabit Ethernet channels (Intel i211AT)
• I/O: DB9 serial port, 2 USB 3.0 external + 2 USB 2.0 internal, three front panel LEDs, pushbutton
• Expansion: 3 miniPCI express (J13 USB or mSATA, apu4*4: with SIM; J14 USB only, with SIM; J15: full miniPCI express, but no SIM, intended for wifi). GPIO header, optional I2C bus, COM2 (3.3V RXD / TXD).
• Board size: 6 x 6“ (152.4 x 152.4 mm) - same as apu1d, alix2d13 and wrap1e.
• Firmware: coreboot
• Cooling: Conductive cooling from the CPU to the enclosure using a 3 mm alu heat spreader (included).

• CPU: AMD Embedded G series GX-412TC, 1 GHz quad Jaguar core with 64 bit and AES-NI support, 32K data + 32K instruction cache per core, shared 2MB L2 cache.
• DRAM: 4 GB DDR3-1333 DRAM
• Storage: Boot from SD card (internal sdhci controller), external USB or m-SATA SSD. 1 SATA + power connector. mSATA is shared with miniPCI express.
• 12V DC, about 6 to 12W depending on CPU load. Jack = 2.5 mm, center positive
• Connectivity: 1 SFP port (Gigabit, Intel i210IS), 3 Gigabit Ethernet channels (Intel i211AT)
• I/O: microUSB serial port, 2 USB 3.0 external + 4 USB 2.0 internal, three front panel LEDs, pushbutton
• Expansion: 3 miniPCI express (J14: full miniPCI express, but no SIM, intended for wifi), J13 USB only, with SIM for modem, J16 USB or mSATA, optional SIM); GPIO header, optional I2C bus, COM2 (3.3V RXD / TXD).
• Board size: 6 x 6” (152.4 x 152.4 mm) - same as apu1d, alix2d13 and wrap1e.
• Firmware: coreboot
• Cooling: Conductive cooling from the CPU to the enclosure using a 3 mm alu heat spreader (included).